Jul-2024 Free NACE-CIP2-001 Test Questions Real Practice Test Questions
NACE-CIP2-001 Dumps Updated Jul 10, 2024 WIith 100 Questions
NEW QUESTION # 42
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Stoning
- B. Acid etching
- C. High-pressure water washing
- D. Sacking
Answer: B
NEW QUESTION # 43
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Review the NCR with the other Inspector
- B. Consult your supervisor
- C. Request a re-blast of the item in question
- D. Verbally challenge the NCR
Answer: B
NEW QUESTION # 44
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Safety
- B. Cost
- C. Appearance
- D. Iron content
Answer: D
NEW QUESTION # 45
All of these are advantages of using repair patches EXCEPT
- A. barrier to moisture and corrosion.
- B. inert to common acids, alkalis, and solvents.
- C. excellent abrasion resistance.
- D. special tools or equipment are required.
Answer: D
NEW QUESTION # 46
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very low reading
- B. No difference from any other coating
- C. Cold flow or creep
- D. A very high reading
Answer: C
NEW QUESTION # 47
Application of Thermal Spray Coatings requires:
- A. Specialized skills supported by training and experience
- B. The same skills as welding
- C. No particular skills
- D. The same skills as liquid coatings
Answer: A
NEW QUESTION # 48
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Require the Applicator to remove the coating
- B. Advise the Owner and write a Non-Conformance report
- C. Stop the job
- D. Ignore the situation
Answer: A
NEW QUESTION # 49
When conducting inspections the Inspector should follow which standards:
- A. NACE and SSPC standards in North America
- B. The specified standards
- C. ISO standards in Europe and Asia
- D. Australian standards in Australia
Answer: B
NEW QUESTION # 50
A failure caused by applying a coating too thinly is known as
- A. cracking.
- B. chalking.
- C. pinholes.
- D. failure to cure.
Answer: C
NEW QUESTION # 51
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Comparable to air blast cleaning
- C. Different than air blast cleaning
- D. The same as air blast cleaning
Answer: D
NEW QUESTION # 52
Coating Surveys are legally required:
- A. On high pressure gas lines and fireproofed structures
- B. On food and beverage vessels and can linings
- C. On commercial marine vessels and offshore platforms
- D. On water tanks and potable water pipelines
Answer: C
NEW QUESTION # 53
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. urethanes.
- C. powder coatings.
- D. inorganic zincs.
Answer: D
NEW QUESTION # 54
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Use the correct solvent
- C. Record the highest value attained
- D. Record the two end points identified in the standard
Answer: D
NEW QUESTION # 55
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Safety Enforcement Costs
- C. Lower Application Costs
- D. Lower Coating Life Cycle Costs
Answer: D
NEW QUESTION # 56
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. 2-Layer Polyethylene (PE)
- C. Fusion Bonded Epoxy
- D. 3-Layer Polyethylene (PE)
Answer: D
NEW QUESTION # 57
An Inspection and Test Plan is required when:
- A. It is always required
- B. When the Owner specifies one
- C. When the Coating Applicator requests one
- D. When the Inspector requests one
Answer: A
NEW QUESTION # 58
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - X cut
- B. Method A - Cross Hatch
- C. Method A - X Cut
- D. Method B - Cross Hatch
Answer: C
NEW QUESTION # 59
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Refuse to take readings until an is in place
- C. Use a generally accepted industry standard and to take readings
- D. Develop your own methodology and proceed take the readings
Answer: C
NEW QUESTION # 60
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. run through the air wash separator.
- B. mixed with uncontaminated abrasive
- C. washed with clean potable water prior to Use.
- D. disposed of properly.
Answer: D
NEW QUESTION # 61
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection only
- B. Visual inspection and Non-destructive testing
- C. Visual inspection, Non-Destructive and Destructive testing
- D. All types of inspection without supervision
Answer: C
NEW QUESTION # 62
......
To become a certified coating inspector at level 2, candidates must pass the NACE-CIP2-001 certification exam. NACE-CIP2-001 exam covers a wide range of topics, including surface preparation, coating application, inspection techniques, and safety procedures. NACE-CIP2-001 exam is designed to be challenging, and candidates must have a thorough understanding of the principles and practices of coating inspection to pass.
View All NACE-CIP2-001 Actual Free Exam Questions Updated: https://quiztorrent.testbraindump.com/NACE-CIP2-001-exam-prep.html
